The Notebook Review forums were hosted by TechTarget, who shut down them down on January 31, 2022. This static read-only archive was pulled by NBR forum users between January 20 and January 31, 2022, in an effort to make sure that the valuable technical information that had been posted on the forums is preserved. For current discussions, many NBR forum users moved over to NotebookTalk.net after the shutdown.
Problems? See this thread at archive.org.

    Undervolting RmClock Windows 7

    Discussion in 'Gateway and eMachines' started by gselsidi, Mar 4, 2009.

  1. gselsidi

    gselsidi Notebook Evangelist

    Reputations:
    33
    Messages:
    312
    Likes Received:
    0
    Trophy Points:
    0
    Hey guys im trying to undervolt my t5550 using rmclock, i got rmclock from the undervolt forum with the vista64 drivers too, and the program runs.

    But it wont let me check off the IDA and DFFS option.

    The multipliers just show 0-5 and all the volts on them are 1.250V
    Is this correct or is rmclock not working and reading correctly?
     
    gselsidi, Mar 4, 2009
    #1
  2. Diablo

    Diablo Metalhead

    Reputations:
    772
    Messages:
    1,471
    Likes Received:
    1
    Trophy Points:
    56
    its not reading the voltages correctly. i had RMclock working just fine under windows 7 using the same voltages i use in vista.
     
    Diablo, Mar 4, 2009
    #2
  3. gselsidi

    gselsidi Notebook Evangelist

    Reputations:
    33
    Messages:
    312
    Likes Received:
    0
    Trophy Points:
    0
    what is the problem then how come its not working?
     
    gselsidi, Mar 4, 2009
    #3
  4. Diablo

    Diablo Metalhead

    Reputations:
    772
    Messages:
    1,471
    Likes Received:
    1
    Trophy Points:
    56
    personally i would go through the guide again and try it again. as for DFFS, is it enabled already?

    and the processor has to support IDA in order to use it. look under your RMclock profiles tab and see if there is IDA listed as a multiplier, if not, you cant use it.
     
    Diablo, Mar 4, 2009
    #4
  5. gselsidi

    gselsidi Notebook Evangelist

    Reputations:
    33
    Messages:
    312
    Likes Received:
    0
    Trophy Points:
    0
    i have a t5550 and no DFFS is not enabled, the box is disabled.
    Does the T5550 support those?
     
    gselsidi, Mar 5, 2009
    #5
  6. Diablo

    Diablo Metalhead

    Reputations:
    772
    Messages:
    1,471
    Likes Received:
    1
    Trophy Points:
    56
    can you post screen shots of RMclock and its tabs?
     
    Diablo, Mar 5, 2009
    #6
  7. gselsidi

    gselsidi Notebook Evangelist

    Reputations:
    33
    Messages:
    312
    Likes Received:
    0
    Trophy Points:
    0
    yea ill try give me a bit, im trying to switch back to vistax64
     
    gselsidi, Mar 5, 2009
    #7
  8. gselsidi

    gselsidi Notebook Evangelist

    Reputations:
    33
    Messages:
    312
    Likes Received:
    0
    Trophy Points:
    0
    its ok cpugenie works fine
     
    gselsidi, Mar 6, 2009
    #8
  9. Kazeari

    Kazeari Notebook Consultant

    Reputations:
    1
    Messages:
    240
    Likes Received:
    0
    Trophy Points:
    30
    Win 7 64 bit here and works fine.
     
    Kazeari, Mar 6, 2009
    #9