The Notebook Review forums were hosted by TechTarget, who shut down them down on January 31, 2022. This static read-only archive was pulled by NBR forum users between January 20 and January 31, 2022, in an effort to make sure that the valuable technical information that had been posted on the forums is preserved. For current discussions, many NBR forum users moved over to NotebookTalk.net after the shutdown.
Problems? See this thread at archive.org.

    How dusty was your computer? Post your post-cleaning temps!

    Discussion in 'Hardware Components and Aftermarket Upgrades' started by Duct Tape Dude, Oct 29, 2010.

  1. Duct Tape Dude

    Duct Tape Dude Duct Tape Dude

    Reputations:
    568
    Messages:
    1,822
    Likes Received:
    9
    Trophy Points:
    56
    tl;dr: Remember to clean your computer!

    I just cleaned out the innards my G50vt after about 6 months of use, it made a world of difference. Below is a compilation of results so far:

    Component Temps Before Temps After Change in Temp Time Between Cleaning Notes[/TD]
    9800m GS 104C (w/ cooler)
    Overtemp (no cooler)
    79C (w/ cooler)
    84C (no cooler)
    -25C 6 months 91C (no cooler) with 20% CPU OC
    9600m GS 100C 67C -33C ~1 Year Post temps include +525/+100/+200 OC
    8400m GS 56C idle
    80C load
    36C idle
    60C load
    -20C idle
    -20C load
    -N/A- Post temps include Antec Big Boy 200mm cooler


    Remember to clean out your vents at least every few months! If your games stutter or lag a few minutes into play, your graphics card and/or processor are likely overheating and throttling down to save themselves.

    When cleaning, remember a few things:
    • Make sure you are electrically grounded before touching your computer.
    • Don't use a vacuum to suck out the dust, it sounds like a good idea but it builds static charge very quickly.
    • Spray air into the vents and gently hold the fan in place.
    • Do not press too hard on the fan or let it spin faster than normal, you could ruin the fan bearings or the motherboard as spinning the fan generates electric current.
    • If you're using a compressed air can, don't turn it upside down when spraying your computer. The liquid inside will come out and could damage some components and/or create condensation (it's still fun to play with on a desk or something if you're careful!).

    I'm curious as to what the average temperature increase is over time.
    So post your results, listing your component, temps before, temps after, and how many months you've left it uncleaned! :)

    If you have a suggestion for to this post, I'll add or modify what I have here.

    Happy cleaning!
     
    Last edited by a moderator: May 7, 2015
  2. Bearclaw

    Bearclaw Steaming

    Reputations:
    463
    Messages:
    1,615
    Likes Received:
    6
    Trophy Points:
    56
    Okay here's a great story.

    Mine wasn't cleaned after like a YEAR of use.

    It was a 9600M GS, and it was getting up to 100C with no OC!

    I cleaned it, and in FurMark with 525MHZ OC on shader 200MHZ on core and 100 on Memory it goes to 73C and then fans kick in and it goes down to 67C, lol

    So now I clean my internals every week.
     
  3. Tsunade_Hime

    Tsunade_Hime such bacon. wow

    Reputations:
    5,413
    Messages:
    10,711
    Likes Received:
    1,204
    Trophy Points:
    581
    My 8400M GS was like

    56 C idle
    80 C load
    26 C ambient

    After cleaning, Antec Big Boy 200mm cooler

    36 C idle
    60 C load
    26 C ambient

    Also stressed when cleaning:

    When using compressed air, hold down the fan with an object not letting the fan blades spin. This again will ruin your fan bearings, but fans will also generate electricity if spun fast enough and will fry your motherboard.
     
  4. Duct Tape Dude

    Duct Tape Dude Duct Tape Dude

    Reputations:
    568
    Messages:
    1,822
    Likes Received:
    9
    Trophy Points:
    56
    Nice results, guys! I put everything so far into a table which I'll continue to update.

    @Bearclaw: That's a pretty awesome improvement considering the additional overclock afterward.
    @Tsunade Hime: thanks for the info, I didn't think about that. It's added to my original post.

    Keep it coming!