DV7-6165 LCD Replacement/Upgrade Instructions

I came across some mention of upgrading the LCD for the dv7-6165 from the factory 1600 x 900 to 1920 x 1080, however I couldn't find any definitive instructions or feedback on the install. I went ahead and ordered the glossy version of P/N LP173WF1(TL)(B3) from laptopscreen(dot)com. They ship out of BC, Canada and it made it to NY surprisingly quick (thanks much!). The install is fairly straight forward if you've ever replaced an LCD screen in the past. If you try this make sure you only use plastic tools to open the casing, as metal can easily scratch as well as cause short-circuits.

Disclaimer: Don't attempt to replace your LCD screen unless you know what your doing! I'm not in anyway responsible for any damage you do to yourself or your computer. Proceed at your own risk!

First I removed the two bottom screws which are hiding behind rubber bumpers. Then I used a couple guitar picks along the top seam of the LCD casing to release the clips:



Once the clips begin to release you'll notice that there is a bit of resistance when pulling on the bezel. This is caused by a few pieces of a very thin double-sided tape that go around the bezel. I used the guitar pick to separate the bezel from the tape, but another thin plastic tool would work fine as well:



With a little care I managed to remove the bezel without breaking any clips. Take note of the metal frame which attaches to both the screen as well as the case in the photo below. I removed the screws holding it to the case and carefully lowered it to set just above the keyboard:



Now I have access to the connector, and can also see the power wires and connector for the HP light (disconnect the connector if this light annoys you):



A quick comparison photo if the line-up between the new and old screens:



Now comes to point where I disconnected the old screen. Be very careful and don't force anything! You can see here where I once again utilize the guitar pick to bring up the piece of clear tape which is adhered over the connector:



I carefully applied a bit of pressure with the tip of the guitar pick to each edge of the connector, alternating between sides until it completely released:



Once the connector was free I stuck it to the casing using the attached clear tape so it's out of the way while I remove the screen itself:



You'll notice that there are four screws on either side of the screen frame which must be removed. Once you get these out you can carefully lift out the old screen (put it somewhere's safe just in case):





I carefully layed the new screen in place of the old screen and re-attached the metal frame using the eight screws I previously removed:



I carefully re-attached the cable to the new LCD making sure to insert it properly so it's seated in the same fashion it was upon removal. I pressed the clear tape back into place. Once I got the connector in properly I went ahead and re-attached the metal frame to the case. I did a quick boot up of the machine to make sure I connected everything properly and didn't damage the screen in the process:



I finally re-attached the bezel to the case assembly. Make sure all of the wires for the antennas and the screen connector are in the correct place. The screen cable can interfere with the bezel clips on the lower left area of the screen where it feeds through near the hinge. Pay attention to this area when putting it back together. Don't try to force the bezel on, but rather use a small tool to move the cable out of the way if necessary:





Hopefully this will be of some help to any other DV7-6165 owners looking for a relatively simple upgrade. Let me know if you have any questions or comments. Cheers!

 

Nice guide! I wished I had this guide when I did mine. The only difference when I did mine is I kept the screws loose making sure the metal frame stays intact.

 

Very nice post

I'm stuck with a crappy 1366x768.

The dv6 being similar, would any 15.6 panel work? Would I need to change to ribbon cable?

I seen in my local store a low res and high res model side by side, everything about the high res model was better, especially the viewing angles.

 

You'll need to find a compatible screen for your particular laptop. There is some information in this thread regarding LCD replacement on dv6:

http://forum.notebookreview.com/hp-pavilion-notebooks/610177-hp-dv6t-display-replacement.html

 

I believe you would need a special cable if you have the dv6. You need the FHD cable

 

Awesome, thanks for the advice. I will be using your guide and screenshots for the replacement of the panel.

I have got on order FHD cable part 656805-001 for the DV6.

And ordered (not from HP) an AUO B156HW01 V4 is the best anti-glare that will fit my DV6-61XX

+1 rep ikny

 

Hi T2050,

could you say me where I can buy the 656805-001 cable? I live in Italy and I hold an dv6-6159sl. Twice: do you thing that the AUO B156HW01 V4 is better than the 653378-001? Third and last , the part 653378-001 is the model LP156WF1(TL)(F3), guess I right?

Thank you Bra!

 

Guys, is the DV7 LCD cable compatible with DV6? I live in Italy and the cost to ship the 656805-001 model here is about 45$. I can find easier the 640900-001 (B3035050G00014). Thank!

 

what is the best screen for a dv7 6180sl?
the screen of the guide is already one of the best? I prefer matte because glossy heavy burden for the view even if I use the laptop to play and navigate.

 

anyone?