The Notebook Review forums were hosted by TechTarget, who shut down them down on January 31, 2022. This static read-only archive was pulled by NBR forum users between January 20 and January 31, 2022, in an effort to make sure that the valuable technical information that had been posted on the forums is preserved. For current discussions, many NBR forum users moved over to NotebookTalk.net after the shutdown.
Problems? See this thread at archive.org.

    tricky networking question: hostnames, ports, and remote access

    Discussion in 'Networking and Wireless' started by Jackboot, Jun 20, 2010.

  1. Jackboot

    Jackboot Notebook Deity

    Reputations:
    69
    Messages:
    759
    Likes Received:
    0
    Trophy Points:
    30
    deleted deleted
     
    Jackboot, Jun 20, 2010
    #1
  2. blue68f100

    blue68f100 Notebook Virtuoso

    Reputations:
    1,020
    Messages:
    3,439
    Likes Received:
    0
    Trophy Points:
    105
    Have you tried using a port forward. This should allow you to use a non std port. Most ISP block port 80 though unless you have a business account.
     
    blue68f100, Jun 20, 2010
    #2
  3. ATG

    ATG 2x4 Super Moderator

    Reputations:
    3,306
    Messages:
    4,461
    Likes Received:
    344
    Trophy Points:
    151
    Not sure but I'll give it a shot.

    How about using a web redirect host type? This way when you type your dyndns address it should redirect to the ip of the ATA with default port 80. Another option is "port 80 redirect"...
    Oh, and I'm talking about no-ip.org options, not sure if DynDns has those but they probably do.
     
    ATG, Jun 20, 2010
    #3
  4. Jackboot

    Jackboot Notebook Deity

    Reputations:
    69
    Messages:
    759
    Likes Received:
    0
    Trophy Points:
    30
    deleted deleted
     
    Jackboot, Jun 20, 2010
    #4
  5. blue68f100

    blue68f100 Notebook Virtuoso

    Reputations:
    1,020
    Messages:
    3,439
    Likes Received:
    0
    Trophy Points:
    105
    I have quit using all std ports (<1024) for outside access into my network. Doing so hides you from snoopers and hackers.

    Another option is use VPN access. I use an VPN Endpoint router (FVS-338) for this. Once the tunnel is setup I have complete access to my network and all is secure against snooping eyes.
     
    blue68f100, Jun 20, 2010
    #5
  6. Jackboot

    Jackboot Notebook Deity

    Reputations:
    69
    Messages:
    759
    Likes Received:
    0
    Trophy Points:
    30
    deleted deleted
     
    Jackboot, Jun 20, 2010
    #6
  7. blue68f100

    blue68f100 Notebook Virtuoso

    Reputations:
    1,020
    Messages:
    3,439
    Likes Received:
    0
    Trophy Points:
    105
    I had some hackers from china that hammered my NAS for 3-4 days before I blocked them with my router. Then I moved the port >1024 and never had a single hit since. The problem with ports <1024 is the snoopers known what equipment is used and any weakness. Go ahead and move it for added security.
     
    blue68f100, Jun 21, 2010
    #7
  8. Jackboot

    Jackboot Notebook Deity

    Reputations:
    69
    Messages:
    759
    Likes Received:
    0
    Trophy Points:
    30
    Good point. I've switched to another port. Thanks again :)
     
    Jackboot, Jun 22, 2010
    #8