The Notebook Review forums were hosted by TechTarget, who shut down them down on January 31, 2022. This static read-only archive was pulled by NBR forum users between January 20 and January 31, 2022, in an effort to make sure that the valuable technical information that had been posted on the forums is preserved. For current discussions, many NBR forum users moved over to NotebookTalk.net after the shutdown.
Problems? See this thread at archive.org.

    Questions about Ordering from HIDEvolution

    Discussion in 'Notebook Cosmetic Modifications and Custom Builds' started by DiMethylSulfoxide, Nov 5, 2018.

  1. DiMethylSulfoxide

    DiMethylSulfoxide Notebook Enthusiast

    Reputations:
    5
    Messages:
    27
    Likes Received:
    3
    Trophy Points:
    6
    My hope is to order a MSI GT75 gaming laptop this month from HIDEvolution, but I had a question for people who have experience ordering from them.

    I have been told that I should get the Thermal Grizzly Conductonaut thermal paste for both the GPU and CPU, however, HIDEvolution, for only $30 more, offers this paste along with the Fujipoly Extreme Thermal Pads. I am a little confused by this, because I have found from forum posts all over the internet that using both thermal pads AND thermal paste is a bad idea, as it could inhibit heat transfer. What is the best option here, if I don't mind spending the extra $30?

    Thank you!
     
    Last edited: Nov 5, 2018
    DiMethylSulfoxide, Nov 5, 2018
    #1
    Spartan@HIDevolution likes this.
  2. Spartan@HIDevolution

    Spartan@HIDevolution Company Representative

    Reputations:
    39,604
    Messages:
    23,561
    Likes Received:
    36,864
    Trophy Points:
    931
    You don't use both Grizzly Conductonaut and Fujipoly Extreme Thermal Pads pads, in the same places. That would be unproductive. However, there are places where Grizzly Conductonaut does not work well, and that is where the Fujipoly Extreme Thermal Pads go.

    I have had the Fujipoly Thermal Pads on both my GT73VR Titan Pro and my current GT75 Titan 8RG. I would not buy these laptops without them. Period! They reduce temps by as much as 5C and every degree down is a huge plus point as these CPUs can get really warm but not if you have the Thermal Grizzly Conductonaut + Fujipoly Thermal Pads + I also have the bottom panel mod:

    [​IMG]

    Don't forget to email [email protected] before you order if you want the NBR Forum discount
     
    Last edited: Nov 5, 2018
    Spartan@HIDevolution, Nov 5, 2018
    #2
  3. DiMethylSulfoxide

    DiMethylSulfoxide Notebook Enthusiast

    Reputations:
    5
    Messages:
    27
    Likes Received:
    3
    Trophy Points:
    6
    Thank you for the clarification! I think I will get both the Conductonaut and the Fujipoly pads. Considering I am likely getting the i7-8850H/GTX 1070 version, I don't think it is worth it to get the bottom panel mod.
     
    DiMethylSulfoxide, Nov 5, 2018
    #3
  4. Spartan@HIDevolution

    Spartan@HIDevolution Company Representative

    Reputations:
    39,604
    Messages:
    23,561
    Likes Received:
    36,864
    Trophy Points:
    931
    sounds like a plan
     
    Spartan@HIDevolution, Nov 5, 2018
    #4
  5. Bobbert9

    Bobbert9 Notebook Consultant

    Reputations:
    43
    Messages:
    139
    Likes Received:
    93
    Trophy Points:
    41
    What exactly is the bottom panel mod? I looked at the picture but I don't know the difference from stock.
     
    Bobbert9, Nov 24, 2018
    #5
  6. Spartan@HIDevolution

    Spartan@HIDevolution Company Representative

    Reputations:
    39,604
    Messages:
    23,561
    Likes Received:
    36,864
    Trophy Points:
    931
    you see those 2 grills? they are not how it is in the stock bottom panel. That mod cuts 2 holes and puts a mesh to allow more airflow and thus reducing temps by 5C. Every degree of reduced temp matters in these high end laptops with the latest CPUs.

    Stock Bottom Panel:

    [​IMG]

    HIDevolution Bottom Panel mod:

    [​IMG]
     
    Spartan@HIDevolution, Nov 24, 2018
    #6
    Bobbert9 likes this.
  7. Bobbert9

    Bobbert9 Notebook Consultant

    Reputations:
    43
    Messages:
    139
    Likes Received:
    93
    Trophy Points:
    41
    Ahhh I see. Thank you. I have a GT73VR ordered but from XoticPC and they don't offer this mod. Since I don't have mine yet I wasn't sure how this was done. That should be stock.

    Sent from my SM-N950U using Tapatalk
     
    Bobbert9, Nov 24, 2018
    #7
    Spartan@HIDevolution likes this.
  8. Spartan@HIDevolution

    Spartan@HIDevolution Company Representative

    Reputations:
    39,604
    Messages:
    23,561
    Likes Received:
    36,864
    Trophy Points:
    931
    100% agreed.
     
    Spartan@HIDevolution, Nov 25, 2018
    #8
  9. Devid

    Devid Notebook Enthusiast

    Reputations:
    12
    Messages:
    28
    Likes Received:
    14
    Trophy Points:
    6
    How to cuts 2 holes in the stock bottom panel ??

    Thanks

    Inviato dal mio SM-G920F utilizzando Tapatalk
     
    Devid, Nov 3, 2019
    #9
  10. senso

    senso Notebook Deity

    Reputations:
    565
    Messages:
    1,645
    Likes Received:
    789
    Trophy Points:
    131
    Hole saw is the easier way to make it nice.
     
    senso, Nov 3, 2019
    #10
  11. Devid

    Devid Notebook Enthusiast

    Reputations:
    12
    Messages:
    28
    Likes Received:
    14
    Trophy Points:
    6
    Yes, but hole saw for cutting edge flawlessly , working fine ???

    Thank you for reply .

    Inviato dal mio SM-G920F utilizzando Tapatalk
     
    Devid, Nov 3, 2019
    #11