The Notebook Review forums were hosted by TechTarget, who shut down them down on January 31, 2022. This static read-only archive was pulled by NBR forum users between January 20 and January 31, 2022, in an effort to make sure that the valuable technical information that had been posted on the forums is preserved. For current discussions, many NBR forum users moved over to NotebookTalk.net after the shutdown.
Problems? See this thread at archive.org.

    MX2 Thermal Paste + M860TU - Where can I put it?

    Discussion in 'Sager and Clevo' started by DRTH_STi, Sep 13, 2008.

  1. DRTH_STi

    DRTH_STi can't.stop.buying.laptops

    Reputations:
    142
    Messages:
    751
    Likes Received:
    13
    Trophy Points:
    31
    I mean other than the obvious processor application - where can I put this stuff?

    Hard drive???

    Memory???

    GPU???

    Man I just want to lather it on.
     
  2. Nirvana

    Nirvana Notebook Prophet

    Reputations:
    2,200
    Messages:
    5,426
    Likes Received:
    0
    Trophy Points:
    0
    between the heat sink and GPU
     
  3. milcs

    milcs Anti-fanboy

    Reputations:
    247
    Messages:
    2,005
    Likes Received:
    0
    Trophy Points:
    55
    Try applying on the brushed aluminium as well... try some nice patterns that will look nice! :)
    The rest, open the back and just put it in... :D

    I'm joking... I have no idea! Just thought your post was quite funny...

    Oh, and try some on those USB, VGA and HDMI holes... I never liked having open holes... dust can get in! :D
     
  4. Bssic

    Bssic Newbie

    Reputations:
    0
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    5
    CPU, GPU, chipset or anything with a heatsink on it

    make sure you completely remove the old paste and use something that will not leave fibers behind
     
  5. DRTH_STi

    DRTH_STi can't.stop.buying.laptops

    Reputations:
    142
    Messages:
    751
    Likes Received:
    13
    Trophy Points:
    31
    alright - i'm going in for the operation. Will be finished by sunday. Will post temps when finished.
     
  6. Neil@Kobalt

    Neil@Kobalt Company Representative

    Reputations:
    1,230
    Messages:
    499
    Likes Received:
    0
    Trophy Points:
    30
    If you're going to do this make sure you clean the old thermal paste off properly as suggested above. You can use something like kitchen paper but after removing the bulk of the material "dry", use Tim Clean to clean the surfaces properly:

    1/ Wipe existing paste off with a dry cloth
    2/ Use a little TimClean on a cloth and apply to chip
    3/ wait 20-30 seconds and dry off TimClean with cloth
    4/ Apply new paste.

    Also remember that, though you should only use a small ammount of thermal paste, you need enough to cover the chip properly. People are often surprised about the ammount of factory applied paste on GPU blocks and of course there's a point that sufficient turns to way too much, just be careful that all. The copper heatpipes are quite delicate as well so take extra care in those too - a slight bend can easily stop the Hs making full contact with a CPU or GPU.
     
  7. DRTH_STi

    DRTH_STi can't.stop.buying.laptops

    Reputations:
    142
    Messages:
    751
    Likes Received:
    13
    Trophy Points:
    31
    Thanks Neil - will do.
     
  8. DRTH_STi

    DRTH_STi can't.stop.buying.laptops

    Reputations:
    142
    Messages:
    751
    Likes Received:
    13
    Trophy Points:
    31
    oh by the way - do I need those little paperlike tabs? Would it be ok to just apply to paste as it without a tab or is a tab necessary?

    Because There's a tab on the heatsink - it's sort of stuck to the heatsink. I should just take it off right?