*** Official Clevo P870DM2/P870DM3 (Sager NP9873/NP9872) Owner's Lounge! - The Phoenix 2 is here! **

Haha give me a little time.. I was changing and updating.. Haven't had time to finish it yet..

 

Can you take a picture of the pad layout, what thickness you put in and the contact pattern left.

 

Haha first time with a 75Hz + display?

 

I had a 75hz panel on my Eurocom Sky X9, this is a 120 hz display. Please read my sig brah

 

I meant first time.using a 75+ Hz display..
I know you have the 120hz one.
I have been using 144hz monitors painful for quite some time, anything lower just feels painful now.

 

oh I had a ROG Swift 144hz screen on my previous Origin PC Millennium desktop but I don't know, I never felt that smoothness, probably because how ASUS matte screens suck, their colors appear washed out as if you spilled a can of grease over your screen, heck I remember on my old ASUS G750JX with a matte screen, it was the dullest screen I ever looked at.

 

Lol.
You need one of them 144hz IPS monitors!
But hey seems like the QHD panel is great!

 

Sure, I'll take another picture when I take it off next. I believe I used 1mm + 1.5 doubled up to make to 2.5mm replace the front pad that's closer to the CPU. I had hoped that would level it off the contact.
Still, the pads made good contact though. I wanted to try 1mm at front and 1.5mm at on the pad next to it but needed to check they'd make contact first.
Needless to say I don't think they'll make a difference due to the way the Heatsink bolts up with the GPU heatsink at the rear.

 

Is Profile 1 more aggressive?

 

Yes it's CL16 vs CL18.

 

What's this... a new super PSU? Sounds very nice.... and exactly what would be needed for 1080ti SLI setup.... hmmmmm......



edit... how can they get a PSU so right... but a keyboard so wrong though?

 

I think its a Eurocom endeavor and not clevo but I could be wrong.

Sent from my LG-H918 using Tapatalk

 

@TBoneSan @Johnksss@iBUYPOWER @Prema

AUO B173QTN01.0 3K 120hz (G-Sync) Spyder5 Pro Screen Calibration Profile

 

Champion!!!!! Rep coming your way... but NBR is telling me to spread the love first. Cheers brother!

 

Please contact Credit Managers @Papusan or @bloodhawk or @hmscott for assistance with your problem.

On a more serious note, let me know how you like it and be ready for v1.1 tomorrow which will be even better
the difference between without the profile and WITH is like night and day difference.

Using the Spyder5Pro software it allows you to compare the difference with an on/off button and man, the normal profile looks so white and dull like a ghost compared to this lively and rich in color profile

 

Rep coming your way from Tbone

 

Doubled up +Rep to @Phoenix

 

+Rep @ Phoenix, thanks a lot mate, much appreciated

 

Thank you so much for the screen calibration Phoenix!!

 

Though I (unfortunately) don't owe that Beast, I am stunned everytime how much selfless effort is put in here to help everyone out and make the day shine a bit more golden!

 

This is so true. You learn so much just by following threads. This is the best community I've seen anywhere. Props to all of you!

 

Im going to need one of those. Pronto!!! Especially since it will cut down on carrying around two of them.........

 

Thanks to @Meaker@Sager

Got my new thermal grizzly pads installed.

Got work in seven hours so I haven't fully tested the system but idle temps are:

CPU: 27C [CLU]

GPU1: 32C [ICD]

GPU2: 29C [ICD]

 

What's your room temp? I'm surprised on how low they are.


Sent from my iPhone using Tapatalk

 

It's cold lol

18C (64F)

 

So this profile is safe to use with any P870DM3 1440p screen?

How do I tell the model of my screen?

Can I save my default profile somehow before applying this one?

 

Another noobie question (man I'm learning so much from this community!), when I run memtest86, should I accept the defaults and just let it run. Or should I go under configuration and change something? Also, how many passes? I'm thinking probably let it run overnight.

Reason I'm running memtest86 is I've had 2 hard locks in BF1, so I wanted to rule out the memory first. I know it's probably the Geforce driver I'm using, v375.86. Everything else has been stable.

 

default settings are fine, let it just run overnight for like 8-10 hours. the number of passes depends on the amount of memory installed in your system (32gigs takes double amount of time than 16gigs, naturally). at 32gigs, i have 3-4 passes overnight and its sufficient for complete everyday stability.

Sent from my Huawei Mate 8 NXT-AL10

 

Overnight it is then, thx @jaybee83.

 

NO!! this is only for that particular screen.

If you don't even know what a screen your laptop has, then please dont even bother.

On a side note, you can check your screen type by downloading AIDA64 Extreme and going to throw monitor section to see your screen model

 

Very nice! I installed my alphacool 14 w/mk pads as well late last night. While I did not see a temperature change, still 44C at idle with background use I am sure the memory is sitting at a better temperature even though I can't measure this. This was at room temp 70 degrees with a single GPU and single heatsync. I would like to thank meaker as well!! How is everyone else doing at idle?

 

Glad I asked. AIDA64 says I have a AUO B173QTN01.0 (monitor ID 1096). Thx @Phoenix .

 

36C.

 

23.3*C (74*F) ambient room temp

35*C minimum on the CPU cores for me...
40*C on GPU
41/42*C on the RAM

I can't even hear the fans running

Spoiler

 

Very nice. You have a single GTX 1080 with the vapor chamber correct? What have been your max temps lately when playing BF1.

 

Yep the single 1080 with vapor chamber... I've only been watching FPS while playing, haha! Next time I play I'll leave the hardware monitor running in the background and report back.

 

Is your CPU overclocked? GPU? Or running stock?

 

With those idle temps I was at:
CPU 4.5GHz (45x4, 43x cache) -70mV
RAM XMP1@3000MHz
GPU stock
"Overclock" fan profile in Clevo Control Center.
Performance mode in Windows/nVidia/CCC

See the "proposed" section:

Spoiler

 

Don't have dual PSUs at work but...here's single GTX 1080 + 6700K temp results. Ambient temp is 20C(68F):

Maximum Fans:



OC Fans:



Automatic Fans:

 

How come I am only getting 25K with SLI???? http://www.3dmark.com/3dm11/11751171



@Mr. Fox @bloodhawk @TBoneSan @GTVEVO

 

I think at stock clocks that's about right on target, mine was 25368 in windows 10.

 

Thanks for the confirmation. I guess they're not scaling as well as I hoped they would.

 

Double check if SLI enabled..
But it seems pretty decent.
Also with Pascal clocks scale with the temperature.

 

offcourse it is bro

 

3DM11 overall score relies on the Physics score as well. Try out Fire Strike and it should be fine.

 

Looking at your combined score it seems you could have some throttling going on. Run the combined test and log your cpu and confirm or look at the cpu graph.

 

That is a bit weird. My 980 Tis can hit 25600. Thought that's with a 5820k @ 4.5GHz.

What's your actual graphics score in that? My record 25700 had a 38182 graphics score.

 

I just received my stock EVOC P870DM3 with a single 1080 and a 1440p120 display. Any recommended modifications? I remember people talking about replacing the fans back when I was following this thread (and by that I mean I'd read all of the 300 odd pages).

 

Regardless I always recommend to get your benchmarks right away so you can determine if you are moving forward or backwards with any changes. After this you will know the first step to take from your results.